Singlr Door Draught Stop
- Stop Draughts
- Reduce Noise
- Save Energy
- Stop Dust and Pollen
- Rain and moisture proof
- Fills gaps from up to 10mm
- EVS DIY Packs
- Permanent solution
- Stop Draughts
- Reduce Noise
- Save Energy
- Stop Dust and Pollen
- Rain and moisture proof
- Fills gaps from up to 10mm
- EVS DIY Packs
- Permanent solution
Do it once... Do it right!
How often have you seen a door that has a gap that ranges from no narrow to wide that allows light and massive draughts. The common solution has been to try and layer foam tape on top of each other plug the gaps. The result is only temporary as these seals often fall off after a short time. What is the cost of getting your property maintenance company to redo failed foam seals? It is better to pay a little more for a quality solution and do the job properly and know that you wont have to return over and over again to fix up failed foam seals.
(Before) Door gaps that cause draughts and energy loss
(After) EVS Draught Stop
EVS Draught Stops the long term solution
Doors can open either outwards or inwards and the seals can be more or less exposed to the weather. EVS Draught seals are an ideal solution as they are made from durable water proof materials that can withstand extreme weather conditions such as wind and rain. They can be left in their pre finished colour or painted to match the rest of the door frame. It is recommended that pre-finished timber profiles are painted with suitable UV protection to avoid fading.
EVS Draught Stop DIY Packs
The DIY Sliding Sash Draught Stop packs provide a solution that is ready to be installed into common sized timber framed windows. There are common sizes of Sliding sash windows and EVS has developed a pack size to minimize waste and make it easier to get targeted installation steps.
EVS Draught Stop DIY Packs
The DIY Sliding sash Pack comes with three lengths of Wide V-Seal that are suitable for Single Door up to 2100 x 93cm. The installation steps are suggested for installing for a typical style window. Each window may have different hardware or timber structures and installation may need to modified to suit your specific window requirements.
EVS Draught stops are available throughout New Zealand and can also be purchased online.
Durable Interior or Exterior
DIY Pack includes:
-2 Sides: Wide V-Seal (210cm)
-1 Top: Wide V-Seal (93cm)
Prefinished in PVC timber or white
Can cover gaps up to 1.5cm
$77.68
EVS Draught stops are available throughout New Zealand and can also be purchased online.
Exceed has a network of skilled Technicians that cover most of New Zealand and provide friendly helpful advice and service for installing your EVS draught seals
Visit their web site and request a quote. www.exceed.co.nz
Selected PlaceMakers stores provide the builders packs of Draught Seals and soon will be offering the DIY packs. If they are not in stock we can get them in usually within a week.
Contact your local store and ask about EVS Draught seals.
EVS is based in Otago and can offer Dunedin and Central Otago customers Draught Stop installation and supply. EVS can provide advice on how to install your Draught stops
Contact us if you want a price or advice. sales@evsdraughtstop.nz
You can use common home DIY tools such as a small mitre saw with a fine tooth blade or a fine tooth handsaw. You will also need a good tape measure, screw drivers, a sharp pencil, and gap fillers
Mark out guide lines around the door frame using the small block on the sides and the wide block on the base with the window in a closed position.
Clean the edges so they free of grease, dust and loose flaking paint. Make sure they are thoroughly dried before applying the edges seals
Measure between the inside faces and transfer the measurements to the top side of the Draught Stop profiles. Make the size a tight fit so if necessary you can trim the length shorter.
The top two Draught profiles are cut at 90° to fit the full width. The lower Draught seals are trimmed at 45° miter cuts to form a nice joint.
Peel the beginning 10cm back tape of from your bottom section and press it firmly into marked position then pull back the rest of the backing tape and press down firmly.
Place each side into the correct position that has been marked out earlier. Do not pin the profiles yet in case further trimming is required.
Install the top and sides on the door frame which may be on the interior or the exterior of the door. If it is the exterior face then it is recommended that you seal or paint the edge to prevent moisture penetration between the seal and the frame.
Install the draught stop across the base of the door if it opens outwards and closes against a raised up sill. If the door opens inwards over carpet or an uneven floor then you will need a Kick-Up seal rather than the V-Seal supplied.
Acrylic gap filler like ‘No-More-Gaps’ can be used to fill the mitre joints. Use a damp cloth to clean the area for a seamless result.
Download your Copy
You can download your copy of the EVS Draught stop for inspiration and step by step instructions on how to install Draught Stop
EVSDraughtSeal.pdf
Phone: +64 (0) 274346912
Email: info@evsglazing.nz
EVS Window Technology Ltd
122 Kaituki Ridge Lane
Queensberry Hills
Central Otago
New Zealand
Email: info@evsglazing.nz
Draught Stop orders Sales@evsdraughtstop.nz
Mobile: +64 (0) 27 4346 912